View CS387H_1228637.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CS3341, CS3351, CS387 Alternator Voltage Regulator Darlington Driver
The CS3341/3351/387 integral alternator regulator integrated circuit provides the voltage regulation for automotive, 3-phase alternators. It drives an external power Darlington for control of the alternator field current. In the event of a charge fault, a lamp output pin is provided to drive an external darlington transistor capable of switching on a fault indicator lamp. An overvoltage or no STATOR signal condition activates the lamp output. The CS3341 and CS3351 are available in SOIC-14 packages. The CS387 is available as a Flip Chip. For FET driver applications use the CS3361. Use of the CS3341, CS3351 or CS387 with external FETs may result in oscillations.
Features http://onsemi.com MARKING DIAGRAM
14 14 1 SOIC-14 D SUFFIX CASE 751A 1 CS33x1G AWLYWW
* * * * * *
Drives NPN Darlington Short Circuit Protection 80 V Load Dump Temperature Compensated Regulation Voltage Shorted Field Protection Duty Cycle, Self Clearing Pb-Free Packages are Available*
CS33x1 x A WL Y WW G
= Specific Device Code 4 or 5 = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package
MAXIMUM RATINGS
Rating Storage Temperature Range, TS Junction Temperature Range Continuous Supply ICC Load Dump Lead Temperature Soldering: Reflow: (SMD styles only) (Note 1) Value -55 to +165 -40 to 150 27 400 230 peak Unit C C V mA C
PIN CONNECTIONS
1 DD GND NC OSC Lamp NC NC
SOIC-14 14 SC NC VCC Sense STATOR NC IGN
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. 60 second maximum above 183C.
Flip Chip, Bump Side Up
DD GND NC OSC Lamp IGN Stator SC VCC Sense
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
(c) Semiconductor Components Industries, LLC, 2005
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet.
1
September, 2005 - Rev. 12
Publication Order Number: CS3341/D
CS3341, CS3351, CS387
VCC
IGN
ENABLE Series Regulator VSUP
Load Dump Detection and Protection
OSC
OSC
Sense
+
+
Regulator Comparator + - VREG R
RS Flop Set Dominate Q
Lamp Indicator S Device Driver R
High Voltage Comparator + - VHV
DELAY
SC ENABLE STATOR Power Up Note: CS3341/CS387 Disconnected CS3351 Connected STATOR
LAMP STATOR Timer VSUP GND
Figure 1. Block Diagram
http://onsemi.com
2
CS3341, CS3351, CS387
ELECTRICAL CHARACTERISTICS (-40C < TA < 125C, -40C < TJ < 150C, 9.0 V VCC 17 V; unless otherwise specified.)
Characteristic Supply Supply Current Enabled Supply Current Disabled Driver Stage Output High Current Output Low Voltage Minimum ON Time Minimum Duty Cycle Short Circuit Duty Cycle Field Switch Turn On Rise Time Field Switch Turn On Fall Time Stator Input High Voltage Input Low Voltage Stator Time Out Stator Power-Up Input High Stator Power-Up Input Low Lamp Output High Current Output Low Voltage Ignition Input High Voltage Input Low Voltage Oscillator Oscillator Frequency Rise Time/Fall Time Oscillator High Threshold Battery Sense Input Current Regulation Voltage Proportional Control High Voltage Threshold Ratio - @25C, R1 = 100 kW, R2 = 50 kW - VHigh Voltage @ LampOn VRegulation @ 50%Duty Cycle - -10 13.5 0.050 1.083 - - - - +10 16 0.400 1.190 mA V V - COSC = 0.22 mF COSC = 0.22 mF COSC = 0.22 mF 65 - - - 17 - 325 - 6.0 Hz - V ICC > 1.0 mA ICC < 100 mA 1.8 - - - - 0.5 V V VLAMP @ 3.0 V ILAMP @ 30 mA - - - - 50 0.35 mA V High to Low CS3351 only CS3351 only - - 10 - 6.0 10 - - - 100 - - - 6.0 600 - 6.0 V V ms V V VDD = 1.2 V IOL = 25 mA - - - - - -10 - 200 - 1.0 30 30 -6.0 - - 6.0 - - - -4.0 0.35 - 10 5.0 90 90 mA V ms % % ms ms - - - - 12 - 25 50 mA mA Test Conditions Min Typ Max Unit
High Voltage Hysteresis
0.020
-
0.600
V
http://onsemi.com
3
CS3341, CS3351, CS387
PACKAGE PIN DESCRIPTION
PACKAGE PIN # SOIC-14 1 2 3, 6, 7, 9, 13 4 5 8 10 11 12 14 Flip Chip 1 2 3 4 5 6 7 8 9 10 PIN SYMBOL Driver GND NC OSC Lamp IGN Stator Sense VCC SC FUNCTION Output driver for external power switch-Darlington Ground No Connection Timing capacitor for oscillator Base driver for lamp driver indicates no stator signal or overvoltage condition Switched ignition powerup Stator signal input for stator timer (CS3351 also powerup) Battery sense voltage regulator comparator input and protection Supply for IC Short circuit sensing
ORDERING INFORMATION
Device CS3341YD14 CS3341YD14G CS3341YDR14 CS3341YDR14G CS3351YD14 CS3351YD14G CS3351YDR14 CS3351YDR14G CS387H Package SOIC-14 SOIC-14 (Pb-Free) SOIC-14 SOIC-14 (Pb-Free) SOIC-14 SOIC-14 (Pb-Free) SOIC-14 SOIC-14 (Pb-Free) Flip Chip Shipping 55 Units/Rail 55 Units/Rail 2500 Tape & Reel 2500 Tape & Reel 55 Units/Rail 55 Units/Rail 2500 Tape & Reel 2500 Tape & Reel Contact Sales
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
4
CS3341, CS3351, CS387
TYPICAL PERFORMANCE CHARACTERISTICS
15.5
15 Battery Voltage
14.5
14
13.5 13 -40
-20
0
20 40 60 Temperature (C)
80
100
120
Figure 2. Battery Voltage vs. Temperature (C) Over Process Variation
APPLICATIONS INFORMATION The CS3341 and CS3351 IC's are designed for use in an alternator charging system. The circuit is also available in flip-chip form as the CS387. In a standard alternator design (Figure 3), the rotor carries the field winding. An alternator rotor usually has several N and S poles. The magnetic field for the rotor is produced by forcing current through a field or rotor winding. The Stator windings are formed into a number of coils spaced around a cylindrical core. The number of coils equals the number of pairs of N and S poles on the rotor. The alternating current in the Stator windings is rectified by the diodes and applied to the regulator. By controlling the amount of field current, the magnetic field strength is controlled and hence the output voltage of the alternator. Referring to Figure 7, a typical application diagram, the oscillator frequency is set by an external capacitor connected between OSC and ground. The sawtooth waveform ramps between 1.0 V and 3.0 V and provides the timing for the system. For the circuit shown the oscillator frequency is approximately 140 Hz. The alternator voltage is sensed at Terminal A via the resistor divider network R1/R2 on the Sense pin of the IC. The voltage at the sense pin determines the duty cycle for the regulator. The voltage is adjusted by potentiometer R2. A relatively low voltage on the sense pin causes a long duty cycle that increases the Field current. A high voltage results in a short duty cycle. The ignition Terminal (I) switches power to the IC through the VCC pin. In the CS3351 the Stator pin senses the voltage from the stator. This will keep the device powered while the voltage is high, and it also senses a stopped engine condition and drives the Lamp pin high after the stator timeout expires. The Lamp pin also goes high when an overvoltage condition is detected on the sense pin. This causes the darlington lamp drive transistor to switch on and pull current through the lamp. If the system voltage continues to increase, the field and lamp output turn off as in an overvoltage or load dump condition. The SC or Short Circuit pin monitors the field voltage. If the drive output and the SC voltage are simultaneously high for a predetermined period, a short circuit condition is assumed and the output is disabled. The regulator is forced to a minimum short circuit duty cycle.
A
Regulator STATOR Winding S
Lamp I Indicator Ignition Switch
FIELD
GND FIELD Winding BATT
Figure 3. IAR System Block Diagram
http://onsemi.com
5
CS3341, CS3351, CS387
REGULATION WAVEFORMS The CS3341/3351/387 utilizes proportion control to maintain regulation. Waveforms depicting operation are shown in Figures 4, 5 and 6, where VBAT/N is the divided down voltage present on the Sense pin using R1 and R2 (Figure 7). A sawtooth waveform is generated internally. The amplitude of this waveform is listed in the electric parameter section as proportion control. The oscillator voltage is summed with VBAT/N, and compared with the internal voltage regulator (VREG) in the regulation
VBAT/N + VOSC VREG VBAT/N + VOSC VREG
comparator which controls the field through the output "Device Driver." Figure 4 shows typical steady-state operation. A 50% duty cycle is maintained. Figure 5 shows the effect of a drop in voltage on (VBAT/N + VOSC). Notice the duty cycle increase to the field drive. Figure 6 shows the effect of an increase in voltage (above the regulation voltage) on (VBAT/N + VOSC). Notice the decrease in field drive.
VBAT/N + VOSC VREG
Field Driver On
Field Driver On
Field Driver On
Figure 4. 50% Duty Cycle, Steady State
Figure 5. > 50% Duty Cycle, Increased Load
Figure 6. < 50% Duty Cycle, Decreased Load
RECTIFIER MR2502 STATOR MR2502 S R3 *C2 10 mF R1 100 kW C3 0.047 mF R2 50 kW C4 0.022 mF R7 10 W VCC Sense OSC IGN R6 20 kW R9 2.4 kW LAMP GND 250 W C1 0.1 mF R4 18 kW SC R5 10 kW F 2N6284 Power Darlington POWER GROUND D1 MR2502
A
STATOR
Driver
FIELD
I
Lamp Indicator IGNITION SWITCH BATTERY
R10 510 W *Note: C2 optional for reduced jitter.
MPSA13 or CS299
Figure 7. Typical Application DIagram http://onsemi.com
6
II II
II II
II II
CS3341, CS3351, CS387
488 mm 506 mm 510 mm
506 mm
605 mm
506 mm 1000 mm 594 mm
2.07 mm
762 mm
742 mm
1.96 mm
Figure 8. Flip Chip Dimensions and Solder Bump Locations, Bump Side Up
http://onsemi.com
7
CS3341, CS3351, CS387
PACKAGE DIMENSIONS
SOIC-14 D SUFFIX CASE 751A-03 ISSUE G
-A-
14 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION.
-B- P7 PL 0.25 (0.010)M B
1 7
M
G C
-T-
SEATING PLANE
K D14 PL 0.25 (0.010)M T B
RX 45_
S
F
A
S
M
J
MILLIMETERS INCHES DIM MIN MAX MIN MAX A 8.55 8.75 0.337 0.344 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 G 1.27 BSC 0.050 BSC J 0.19 0.25 0.008 0.009 K 0.10 0.25 0.004 0.009 M 0_ 7_ 0_ 7_ P 5.80 6.20 0.228 0.244 R 0.25 0.50 0.010 0.019
PACKAGE THERMAL DATA Parameter RqJC RqJA Typical Typical SOIC-14 30 125 Unit C/W C/W
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
8
CS3341/D

▲Up To Search▲

Price & Availability of CS387H

	To Download CS387H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .